Home

How to finish a maple fretboard

How to Clean a Maple Fretboard Sweetwate

Raw maple fretboards are typically oil finished by the manufacturer, so any compatible, non-abrasive fretboard treatment from our shop will work. Remove the strings prior to cleaning the maple fretboard. Use a lint-free microfiber cloth to massage the conditioner into the fretboard. Buff out the remaining cleaner with another microfiber cloth Here's a maple/RW neck for a customer build. Vintage tinted the wood, then applied about 12 coats of Tru-Oil and buffed by hand. The fretboard was worked by me then treated with Fret Doctor. The neck is like your favorite air guitar

Standard procedure is finishing the fretboard with the same finish material as the back. (eg: lacquer on back, lacquer on fretboard) I have never used any Dingo Tone products, nor do I use any wax products, but I would strongly advise against applying any wax to unsealed timber like a maple fretboard Since its maple you can just spray acrylic lacquer over it (first lightly sand it with 400 grit sandpaper) pile several coats (not too thick ones) on until a spray can (or maybe a bit more) is finished,leave it for at least a couple of weeks (better a month) to gas out and then do the final sanding levelling of it.Then go up the grits to remove the scratches and finish it with whatever automotive buffing compound you want or have available...

Pay them to finish the neck. Tru Oil is, essentially, boiled linseed oil, and while it can be (and is) used on the back of a lot of necks, it's not really appropriate for a maple fretboard. It's a.. Maple will look like.... on the quick if you don't put a finish on it. A light oil coat (Tru-Oil or Tung oil), or a thin satin lacquer will give it the unfinished feel, but with some actual protection. HaMMerHeD, Oct 1, 2015 # I used poly on a maple fretboard Warmoth neck a couple years ago. Two coats 20min apart, sand, repeated till 6 coats. After the final coat I sanded up to 600, then used steel wool, then stewmacs.. A 1972 Fender P-Bass neck came into Dan Erlewine's shop with a nasty curve that wouldn't adjust out. Dan had to remove wood to make it straight, so now he's.

How to properly clean & condition an unfinished maple fretboard with MusicNomad's F-ONE oil. It's 100% natural and contains NO lemon oil or acidic properties.. a bright canadian maple fretboard. i know maple can get dirty pretty quick so i am searching for a method to seal/protect the wood WITHOUT having to put clear coat on! will TRU OIL work on this? maybe something else? i am looking for a satin like finish that does not feel sticky. cheers FI Finishing maple can help emphasize the natural wood grain and boost the color of the wood. If you want to make a piece of maple stand out, you can use either oil or wood stain to finish the wood. No matter what you use on your wood, be sure to sand it first and seal it afterward to protect it from any damage Dave talks about using tru-oil to finish a new telecaster maple guitar neck The obviously finish every single maple fretboard on their guitars. 1. Share. Report Save. level 2. Luthier 5 years ago. Fender gloss finishes are applied after fretting. You spray the board/neck frets and all. If you want to avoid finish piling up on/next to the frets, you scrape it off of them after each coat. It's a lot of work and not.

Oil finish on a maple neck/fretboard? The Gear Pag

  1. Maple is a naturally porous wood, which means that the majority of maple fretboards are sealed with nitrocellulose or a lacquer finish. This means that when you're playing the guitar, you're actually playing on the finish of the fretboard rather than playing on the actual maple wood itself
  2. The neck of your guitar deserves as much care and attention as any other part of it, if not more. In this video we talk about how to put a finish on your gui..
  3. For part two of this guitar kit build series, I'm showing how to finish a neck with Tru Oil. This is a nice easy finish to apply, and it gets really good, pr..
  4. Finishing Maple . As with other hardwoods such as cherry, maple can be a bit temperamental to finish, particularly when staining. When applying a stain, be sure to use a pre-stain conditioner to try and even out the blotchy patches that tend to appear. This won't completely solve the problem, though
  5. Start with full strength yellow in a bowl. Add warm water until the color isn't too strong when wiped on your piece of scrap maple. Then add little drops of full strength brown and red to amber it. When you think it's right, test it on your scrap maple & put on the clear lacquer
  6. If you have an unfinished maple fretboard, apply a thin line of fretboard oil (about the width of a cell phone charger cable) directly to the fretboard and rub it in with a paper towel. Buff it with a clean, dry microfiber cleaning cloth. 7 Wipe each fret with a clean paper towel
  7. I played a few beautiful new strats at Guitar Center - they sound great and are clearly well made, but I really don't like the extra thick finish on the maple neck and fretboard. It feels really sticky to me. I played my brother's 79 with maple neck/fretboard and it felt much better to me
Custom Made Guitars, Hand Made Guitars, USA Custom Made

How to finish a maple fretboard - Pit Bull Guitar Forum

  1. The finished part of a maple neck WILL make the neck feel sticky but even an unfinished maple fingerboard will feel different than a rosewood one. The rosewood will have bigger pours, more open grain, and your fingers will actually feel those crevices and ridges. Maple will feel smooth because the grain is closed
  2. uets depending on the ambient air conditions flip over and do the other side the same way. Let the piece dry between coats and keep the coats light
  3. I have done a lot of rosewood board necks and a few maple fretboard ones but I want to get better. I seal it, nitro it, tint clear, more of whatever is needed. But when it comes to polishing and scraping the frets, I need some advice. How are you sanding and polishing the fretboard? Are..
  4. ated' or 'lacquer' finish, unlike newer guitars. Even lacquer finishes maple fretboards on newer guitars can be dulled over time with high purity.
  5. eral oils have been traditional fingerboard preservatives, but they don't dry completely hard, often leaving a sticky playing surface
  6. Hi - I just did a maple/maple neck in TruOil a few months ago and it came out great. I'll put up pictures soon. It is without a doubt better feeling than my nitro necks. It doesn't have the really shinny finish you get from Nitro - but the feel is amazing, and it still looks great. I had no hassles at all
  7. In terms of playability, a guitar's neck is the most important component of a guitar. It's the primary interface, and if there are problems (e.g. uneven frets, too much / or too little neck relief) the guitar will ultimately be more difficult to play. However, it's not only neck relief and the condition of your frets

Maple Neck/Fretboard Finish Help! Fender Stratocaster

I seat the frets, file the ends flush with the fretboard edges, and bevel the fret ends. No fret levelling or dressing at this point. Then I spray on the finish over the top of the frets. Then I do the fret levelling, crowning and dress the fret ends, which takes the finish off the frets The maple fretboard is a little rough to the touch and needs a little sanding. I'll do a full level and crown on the frets, but I thought getting the fretboard finished first would be prudent. I started with 600 grit paper and it feels really good, but the brand new paper left the fretboard dirty I'm doing a Tung oil finish on the back of the neck and sprayed 3 coats of satin Polyurethane on the fretboard. I then used a 800 grit sandpaper then quad 0000 steel wool to get that fast finish. What I'm trying to achieve is the same feel the new Charvel So Cals have on their satin finish maple necks Hi, I have this flame maple fretboard blank: [IMG] I know I have to finish it (because it's maple), but i don't want to use a.. You can probably sand (anything), even use solvent lightly (on nitro), to remove finish on a fretted neck, since wear occurs between frets anyway. If you get down to bare maple, you can rub in anything from thinned ink to stain

Guthrie Govan USA Signature HSH Caramelized Ash | Artist

Maple fretboard finish - Ultimate Guita

I usually just tape off the fretboard and shave the finish off the frets once the finish is cured using a single-sided razor blade. Finish usually comes off in thin strips, but there's no fight in any case. Then, do the normal leveling/crowning/dressing/polishing thing. Pull the tape, wipe it down with naphtha, and call it a love story Do Roasted Maple Necks Need a Finish? Although torrefied necks do not require finishing, most luthiers apply a finish. This is often done in same way that unroasted necks are finished. Common treatments include Tru-oil, wax, etc For this test I decided to try a cheap eBay neck for $33.25 from China. It has a thin urethane finish, but the price isn't the issue as the maple should still age like a $300 neck:. Truth be told, it isn't a bad neck, although it lacks the fret leveling and cleaning that you would expect from a better seller

Maple fretboard with no finish? SevenString

  1. I'd also encourage detailed information from Fender about what the original finish is. Whether it's tinted sort of thing. I once had a '57 vintage reissue which I refretted. On a maple neck that involves refinishing the fretboard. Except the nitrocellulose that Fender advertised wasn't really. It was some catalyzed tinted garbage
  2. Flame Maple Torrified x African Blackwood Fretboard. The finish also helped accent the flames in the neck, not saying you want a flame, but with the degree of coloring my neck has, and the clear satin finish, it looks more aged than it is unless you get up close and inspect it
  3. I far prefer a satin finish on maple necks vs gloss. A satin finish is nothing more than sanded down gloss. You can do this by using ultra fine steel wool #0000. Sounds bad but it doesn't harm the wood at all
  4. The maple fingerboard looks very dirty, I assume the finish has worn down to the bare maple and the dirty has been soaked into the neck. Is there an easy way to get the brand new maple look? Is it just a case of sanding and refinishing? Would the frets have to be taken out? Heres a photo of the neck

Every maple MIM I've seen had a satin finish, which most people think less sticky than a fully lacquered gloss finish... In any event, try some fast fret or just get a bit of light mineral oil from the drugstore and see if a little wipe helps I've also never finished a fretboard (all of mine are either rose or ebony) but you will have to deal with either masking the frets (sounds like a pain) or scraping them (ditto). I use steel wool to clean frets and the board, but trying to get the finish off the frets and not the board is going to be a real hassle So, the next bass I'm looking to buy has a satin, catalyzed polyurethane finish on the maple neck and maple fretboard. This is a pretty modern looking bass, and I want to keep the maple fretboard looking as if it is brand new for years to come and never discolour as some vintage basses/guitars do Step 9: Finishing the guitar body with Tung Oil, Wax or Buffing Oil. Lastly, you will want to apply a clear finish. There are two reasons for doing this. Firstly, the clear finish seals the timber and provides the nice oiled, semi-gloss finish that appeals to most guitar owners and secondly the clear coat will help protect the surface of the. The best way to apply oil to a fretboard is with an old rag that you dab a small amount of oil on to. You then gently rub the oil into the wood, wiping away any dirt that has previously built-up. Remember, you only need a small amount between each fret. You want to see a light sheen and no oily film left behind

Is polyurethane the best finish for a maple fretboard

The fretboard looks great and feels smooth, never sticky. ColorTone Fretboard Finishing Oil works best when applied sparingly—a single bottle goes a long way! Simply wipe it on with a soft cloth, wipe off, and buff. It's guitar-safe when properly used: won't loosen or stain inlays, frets or bindings Maple is very easy to finish, and on an all maple neck it makes sense to have uniformity in the appearance between the fretboard and rest of it. Sand it, then just spray everywhere, very quick. Rosewood can be awkward to finish (needs grain filler, sealer, then top coat)

How to stain a Fender maple fretboard - YouTub

How to Clean & Condition an unfinished Maple Fretboard

Preparing the maple for stain is easy, finish sand down to 400 grit going with the grain of the wood as you sand. Wet the wood with water before staining and let dry, this opens the grain to accept the stain evenly, then sand out with 320 grit going with the grain. Apply your next color. Let dry, then apply your poly or nitro sealer Ebonizing a Rosewood Guitar Fretboard: You can make your rosewood fretboard a nice piano-like black in a few easy steps. It doesn't take much in the way of parts or time, and the result looks fantastic. I started with a Mighty Mite Neck (CR2910) which has a rosewood finish on the Since maple is a porous wood, maple fretboards are usually coated with a lacquer or nitrocellulose finish. This can make the neck look glossy. Depending on the quality of the finish, it can have a huge effect on the feel and playability of the instrument On maple necks with maple fretboards the entire neck is finished, including the fretboard, frets, and inlays. We do not remove the finish from the frets. This work is left to the end user, as part of the set up, assembly, and fret leveling process

To preserve the bright color, most modern manufacturers will spray maple fretboards with finish before the frets are pressed in. The finish reacts with the wood, acting as a light stain that yields the distinctive yellow-gold maple necks we all know and love. The finish, whether nitrocellulose or polypropylene, acts as a protective barrier. I went with a maple neck/maple fretboard on my first build and have read many how to's. It was out of my budget to have the neck finished by warmoth. Though, I do not want to fall into the possible 10% with a warped neck. If not for that I would just play it raw. I prefer to keep it as close to natural color and do not care about ruining the. Be Careful When Adding A Roasted Maple Guitar Neck. While there are advantages such as being less expensive when no finish is required and the fact that the roasting process brings out a beautiful caramel color in the wood. There are drawbacks when adding a roasted maple guitar neck

Sealing/protecting a Canadian Maple fretboard

  1. The maple fretboard is coated with a lacquer finish and get used over time. Maple has less sustain than a rosewood fingerboard and the sound is crispier, drier... sort ofspeak. The rosewood fingerboard has no finish and the sustain is better andthe sound is fatter than a maple fingerboard. Many country singer / guitarist prefer the dry sound of.
  2. Super glue bonds nicely with polyester and polyurethane, like the finish on this guitar. Using super glue as both a filler and a finish turned a tricky repair job into a fun afternoon's work... I cleaned the fretboard edge with naphtha, running a naphtha-dipped paper under the edges of the frets to soften any built-up dirt so I could scrape.
  3. well i was looking around the web to find out if it did any real damage, since i just bought a bottle of Dunlop 65 ultimate lemon oil, and only was mo..

Below are some pics of a mid 1970s maple board Fender Strat refret in process; the board has been defretted, reradiused, prepped, refinished and new frets installed over the finish - these pics are prior to the final fret leveling and fret end shaping (but they will be left fairly straight as the OEM bridge has the wide 2 7/32 string spacing. Like the final fret dressing, the fine-tuning of the nut will be done once the neck has been sprayed with lacquer. Spraying the finish. I want to spray a light tint on the neck to give it a slightly aged appearance. A 1969 neck would have been finished in polyurethane which doesn't yellow much so I don't want to add too much colour The Tele has an all-maple neck meaning body and neck appearance mismatching will occur later on similar to the all-maple neck Strat. Concentrate on rosewood fretboards only with Road Worn models, and yes you will get a great nitro coated guitar out of it This particular guitar neck is a Fender Telecaster from the early 1970s, and it was about to get a serious overhaul. Here's what it looked like before I started - very shiny with a thick polyurethane finish: First order of business after removing the neck was to tape off the areas of the neck that were to be left alone Finish streaks; Debris in the finish; Thickness planer marks on every stair tread (new install) Maple is light in color, hard and has a closed grain. If you understand these three factors, you will sand a maple floor very successfully. Because maple is so light, scratches will not be so easy to spot like on oak floors

1. Clean the wood with mineral spirits or turpentine to remove the top layer of wax, grime and degraded finish. Scrub the area in light circular motions with fine steel wool if the black stain. Find helpful customer reviews and review ratings for Kmise MI0051 Neck for Stratocaster Replacement 22 Fret Maple Fretboard vintage Gloss Finish at Amazon.com. Read honest and unbiased product reviews from our users Hi all, I'm looking for some advice on how to finish my maple fretboard and my neck as well. I've read about tru oil and have considered that, but I was hoping to get something similar to a vintage amber colour for it, if there is anything people recommend to use or on how to apply it as well. Thanks, Be

Maple fretboards: Maple fretboards must not to oiled no matter what. They either have a thicker layer of lacquer or are without any finish at all. Oils and conditioners might damage the lacquer so the simple wiping of the maple fretboards would do the trick A maple fretboard does not really need conditioned ever because it is a harder fretboard than rosewood. Maple fret boards typically have a finish like lacquer or polyurethane and do not require any conditioner. Why do I need to condition a fretboard? Answer: A dried fretboard can split and crack. It can lead to the fret wire or binding to come. The fretboard has no finish at all, except on the sides. If you do sand back, the side of the fretboard should be sealed, CA would work best. Wipe on poly would be an absolutely terrible finish for a guitar neck. It will not be truly hard, and when you rub your hand up and down it will get sticky

Applied by spraying, brushing or wiping, this finish looks like plain sanded maple. To pop the grain a bit, first wipe the maple with an ultrapale shellac sealer. The CAB stands for cellulose acetate butyrate. This will give you more wetting-out of the cellulose and hence more figure The neck is maple, has a rosewood fretboard, black binding and clear nitro-cellulose lacquer finish. The original neck has a 20 mm deep crack across the headstock glue joint, through the lacquer. The spare neck I have been able to find has a 50 mm deep crack at the bolt-on neck joint, and is from 1982. The wood is somewhat better on the original

Fender Jazz Bass Am Standard 2003 - www

4 Ways to Finish Maple - wikiHo

Finishing a Maple Guitar Neck with Tru Oil - Part 1 - YouTub

Basically what I read the natural finish woods (rosewood and ebony) require any oils. The implication is the maple boards can be cleaned with anything that won't damage the lacquer or leave residue behind. I occasionally use lemon oil on rosewood and ebony fretboards I know of guys who used an oil finish on the back of the neck. I do not like that finish. Sometimes gets tacky. The fretboard does not have to be finished. You can use lemon oil on it to protect it. Lemon oil works great with rosewood. I do not like it with maple. I prefer the slick feel of lacquer or urethane on the fretboard. You put on many. I did a black dye on a regular maple neck, it had a little bit of figure in it and came out pretty good. I put about 5 coats of satin nitro on top of the dye. Also did a blue dye on a Floyd Rose Discovery neck, wanted a faded denim look. It is tough to not get streaks in the dye with maple. Dilute it well and many coats. Ro

The neck is shaped, need to clean those burn marks . The headstock is shaped . Cutting the wenge to fretboard dimensions . Preparing to cut fret slots . Fret slots are cut . Cutting stripes of maple veneer for binding . Cutting stripes of wenge for binding . The maple is veneer is glued on are the wenge is next . The fretboard is bound, needs. Generally speaking acoustic guitar fretboards don?t have a finish on them. In fact usually only maple fretboards do and they are almost solely in the realm of electric guitars. Ebony fretboards don?t have a finish on them The ultra cool wore out maple fretboards are finished with Nitro Lac. It's thin and wears easily. (And in some cases, is sticky and traps the dirt where it's played most) The whole reason that Leo Fender switched to Rosewood fretboards in the early 60's was because of the easy wearing maple boards. Dogbite - Your Strat is from the 80's, right

Finishing maple fretboards : Luthier - reddi

Maple Fretboard Sound and Characteristics. Maple is a dense, hard tonewood that produces bright, snappy tones. In the context of a guitar fretboard, this means precise, articulate notes with good bite and a tight low end Even when you seal the maple and apply a stain, the color may be more uneven than you'd prefer -- and there's an easy way to remedy that. Apply a coat of finish, and then tone the wood by spraying pigment on the dried finish or wiping on a gel stain Using appropriate fretboard conditioners such as lemon oil and keeping the guitar away from extreme changes in temperature and humidity are recommended. Ebony is a fantastic fretboard wood choice but it definitely requires more maintenance than rosewood or maple

Rosewood vs Maple Fretboards: Which is Better? - Guitar Spac

For satin-finished maple, a slightly damp cloth will do. Lacquered maple fretboards should only be cleaned with a damp or dry cloth. Using steel wool, no matter how fine, will take away the shine, leaving a matte-like finish. Lemon oil will also take away the sheen Maple fretboards are most often lacquered with an amber tint but there are some that are not. Many fretboards begin life as a satin or matt lacquer which as you play it will self polish turning it gloss, many folks often mistake a satin lacquer for unfinished as it feels a little rougher

Re: Maple fretboard's finish comming of, yelp! Fender uses nitrocellulose lacquer on their fretboards, which is why it ages to the yellowish color you see there. There are TONS of threads on Strat and Tele forums about making repairs like this A bubinga fingerboard, like a maple fingerboard, to which it is actually more similar, really should be finished out, because it doesn't have the natural oils and resins that true rosewood has, which is the main reason those species are used for fingerboards, especially lesser expensive fingerboards The best way is to use a small spray gun and mix some amber tint into the lacquer, spray until you get the color you want then spray a few clear coats over the top. Sand with each step from 800 grit wet and dry (wet) up to 2000, then buff with medium and fine compound. If it is poly you have a couple of choices Why would you use maple if you want a dark finished product? I dont understand. If you want figure, thats OK. But you will have to use a sealer if you want some sort of uniform finish on maple. Dye is a better bet, but only if you want pop. #4 posted 10-07-2010 05:04 PM. Both your woods are notorious for blotching Firstly, finish sand your figured wood to a reasonably high grit such as 400. Raise the grain by wiping it down with a clean cloth wetted with distilled water - do not soak it! Sandpaper acts like millions of sharp edges, slicing and mangling wood fibres at a microscopic level. Some may be loose, distorted or otherwise junky

How to finish a guitar neck - YouTub

Never use steel wool on a maple fretboard that has a glossy finish, as the steel wool will only remove that glossy finish and make your fretboard hazy looking. Using 0000-grade steel wool isn't going to damage the frets or the fingerboards on your instrument, so don't worry! Just ensure that you're extremely gentle with the pressure you. Personally, I don't care for gloss finished necks. I find that my hand doesn't slide very well. I do have a Warmoth finished satin nitro maple neck. That feel fantastic to me. If you order a maple neck with a maple fretboard, the fretboard does get a finish coat. And as DMRACO says, it doesn't change tone quality

How to apply: Clean the wood with naphtha and sand to 600-grit. Mask off the nut, binding and anything you don't want to stain You can spray with the neck hanging vertically, but I like to spray with it in a horizontal position. I spray the headstock face, sides and fretboard then flip the neck over to spray the back. It rests on the nut and last few frets so, exercising care, this can be done while the lacquer is still wet Stingrey maple neck finish. Just got a 2015 Stingrey, first time for me, Im all excited and with a lot of fears because it is a second hand. Theres is this issue? with the neck. Its seems that the neck and the headstock in the back do not have the same finish. The neck feels like natural wood, like a bare wood finish, different to the.

Finishing A Guitar Neck With Tru Oil - Solo Music Kit

Sup all - I have a Fender US Deluxe strat with maple neck that is about 5 months old, so the neck isn't exactly dirty to the core. I just want to clea.. Worst maple neck finish there is. Irritates my fret hand and feels sticky. Yes, through many hours of play, the nitro wears down and the neck starts feeling better. Screw that. I'm much happier not having to constantly subject my fret hand to skin irritation over a period of months just to get a correct-feeling neck Areas like the input jack and bottom edges of a guitar often receive a lot of damage from drops or pokes. Over time, many players rub away at the finish towards the back of the guitar where their forearm makes contact with the body. You could even relic the fretboard itself to simulate years of exposure to strings and oil from your fingers Mineral oil has no such cautionary tales. Like all these oils, though, it is not for use on maple fretboards, but unfinished dark woods like rosewood and ebony. What to do: Remove your strings. Dab a little spot of mineral oil on a clean rag. Rub it into the fretboard. Let it sit 10 or 15 minutes. Rub off all excess with a clean, dry rag. Be.

Norwegian Wood Series Guitars | T-Style, Cream-T/Billy

Tips for Woodworking With Mapl

If you're interested in making your own instruments at home and want to save money, you may be interested in our DIY guitar kits. We sell a variety of different DIY guitar kit options to make electric DIY guitars from the simplest shapes to more complex ones This occurs for two reasons. First, older Fender guitars (i.e., those from the 1950s and '60s) had a nitrocellulose lacquer finish that tends to darken with age. This is accelerated when a guitar was played consistently in smoke-filled clubs and halls. Today's Fender maple necks usually have either a polyurethane or polyester finish. These. 1974 Fender Jazz Bass with Maple Fretboard / Sunburst original finish. Excellent. $5,524.54 + $218.07 Shipping. Add to Cart. Make an Offer. This seller is open to offers. Watch. Shipped From. Diego's Gear Garage. London, United Kingdom. 32. Joined Reverb. 2017. Message Seller. Payment & Returns. Find More on Reverb Early Musikraft neck- caramelized tiger flame maple. Strat 21fret R5 Floyd Rose 1 3/4 nut 2 3/16 neck pocket rosewood face dots truss adjustment at heel drilled for gotoh tuners 10 mm Birdseye fretboard 6150 med frets gun stock oil finish and steel wooled Would look great on a Charvel San Dimas relic axe Flat shipping to CONTINENTAL U.S. LACQUER FINISHING PROCESS - SIMPLE OUTLINE. PREPARATION OF WOOD BEFORE FINISHING. All surfaces must be sanded smooth and scratch-free - Sand to 220grit on hardwoods. Repeat this sanding process on the softwood top - Sand top to 320 grit. Totally remove the sanding dust from all surfaces. Mask off the fingerboard and cover the soundhole

Body Finish - Gloss Polyurethane; Body Shape - Stratocaster® Neck Material - Maple; Neck Finish - Satin Urethane with Gloss Urethane Headstock Face; Neck Shape - Modern D Scale Length - 25.5 (648 mm) Fingerboard - Maple; Fingerboard Radius - 10 to 14 Compound Radius (254 mm to 355.6 mm) Number of Frets - 22; Frets Size. Classic Series '50s Telecaster® Neck, Lacquer Finish, 21 Vintage-Style Frets, Maple Fingerboar I have a PRS Zache Myers SE which has a fitted not bolted satin neck , Top Wood: Quilted Maple with satin finish. Back Wood: Mahogany with satin finish. Number of Frets: 22. Scale Length: 24.5 Neck Wood: Mahogany with satin finish. Fretboard Wood: Ebony. Neck Shape: Wide Fat. Fretboard Inlays: Birds

1978 Gibson Les Paul Standard - Tobacco Burst-Vi76GiLPStdTB018G5191BK Tim Armstrong Signature Electromatic Hollow BodyRock N’ Roll Relics Heartbreaker in Lemon Burst | Rebel1965 Fender Mustang - Daphne Blue-Vi65FeMustDB97743
  • Workcover NSW white card.
  • Standard short circuit current ratings.
  • Toys R Us sales Associate resume.
  • Porcelain sink Refinishing Kit.
  • Free page borders for Teachers.
  • Which of the following definitions best describes an enhancer?.
  • Day month year format.
  • Free trade examples UK.
  • Killing nutgrass with sugar.
  • Can you soak electric stove coils.
  • Thailand smartphone users.
  • Hello beautiful lady in Spanish.
  • VCF format contacts.
  • Convert unlike fractions to like fractions calculator.
  • Blood alcohol limit Victoria.
  • How to tell if your fish is pregnant molly.
  • Chicken sausage and peppers pasta.
  • Wickes decking joists.
  • Private endoscopy London.
  • What spray to use for potato gun.
  • Counting in Spanish to 100.
  • 2012 Audi A4 reliability.
  • Lasko Fan with Remote Walmart.
  • Old Briggs and Stratton carburetor adjustment.
  • Kesavan Theatre Attur show timings.
  • MTDC Matheran.
  • Celebrating 5 years in business.
  • Garage door light bulb not working.
  • Walmart Stereo CD Player.
  • Fridley Theaters Spencer iowa.
  • Twitter widget ID.
  • Dealer network strategy.
  • CSS hyphens not working.
  • How to shape a beard.
  • Danforth pewter locations.
  • How long can you leave onions in the ground.
  • How to erase all data from CD.
  • How to send food overseas.
  • Government fiscal year 2021.
  • Breastfeeding while pregnant miscarriage.
  • Starbound server admin.